1) Preparation for unwanted hairs removal procedure

1.1 Heat the wax in a professional wax melter to a working temperature of 38-39°C in accordance with the operating conditions of the device.

NOTE! Non-compliance with the temperature regime can lead to irritation or skin damage.

1.2 Use PRE-WAX REFRESHING LOTION for skin cleansing and degreasing. Wipe the necessary areas of the skin using a cotton pad, soaked in lotion, immediately before starting the unwanted hairs removal procedure. Leave until it is completely dry.

1.3 If necessary, apply a small amount of talc to the skin in the area of depilation.

2) Wax application and unwanted hairs removal

2.1 Apply an even layer of wax to the skin using a spatula, regardless of the direction of hairs growth.

NOTE! During the application it is necessary to slightly pull the skin in the opposite direction to the spatula.

NOTE! For the convenience of tearing off the solidified wax, it is recommended to leave a small «petal» (that can be grabbed later) or fixate a working tool on the «petal».

2.2 After solidifying (in 8-10 seconds) with a sharp move, remove the wax, after pulling the skin in the opposite direction of the tearing off.

NOTE! Wax that is ready to be torn off should not be soft or be sticky to the hands when touched.

NOTE! The tearing off must be performed in the direction going away from yourself and parallel to the skin.

NOTE! After the wax has been torn off, there can appear slight redness on the skin, which is a normal skin reaction.

2.3 Repeat the procedure on the next area in cases where this is necessary.

3) After unwanted hairs removal procedure skincare

3.1 Once the depilation is finished, use the AFTER WAX REPAIR SERUM for skincare and redness reduction. Apply the serum to the skin and leave until fully absorbed.

3.2 Use AFTER WAX PROTECTION MASK to narrow the pores after the procedure of unwanted hairs removal and UV-rays protection. Apply a thin layer of the cream-mask – using massage movements – to the skin and leave until fully absorbed.

RECOMMENDATIONS «BEFORE» AND «AFTER» FACIAL HAIRS REMOVAL

Avoid touching the skin in the hairs removal zone for at least 30 minutes after the procedure.
Refrain from applying any decorative cosmetics to the treated area for 12 hours after the procedure (tonal foundations, BB/CC creams, and concealer).
Do not subject the treated skin to aggressive cosmetic products or procedures for 24 hours after the procedure (scrubs, peels, laser treatments, etc.).
Minimize sun exposure and UV ray exposure for 24 hours before and after the procedure to protect your skin.

WARNING

Never leave the professional wax heater on when the wax container is empty. Clean the wax heater using oil-based products specifically designed for wax removal (do not use acid-based cleaners). The wax heater is not intended for use by unsupervised children. Do not place plastic containers with wax directly into the heater unless specified by the wax manufacturer. Avoid using the wax heater near bathtubs, shower stalls, sinks, or other water containers. Do not allow wax to come into contact with the temperature regulator.

There are absolute restrictions for the procedure of removing unwanted hairs, including:

- Individual sensitivity to the ingredients.
- Presence of any skin irritations in the designated area for hairs removal.
- Couperosis (pronounced capillary mesh), moles, and warts in the area where hairs removal is intended.
- Recent application of aggressive cosmetic products to the skin in the hairs removal zone just before the procedure (brow lamination, bleaching, etc).

1. DENSE WAX: ROSIN, GLYCERYL ROSINATE, PARAFFIN, BEESWAX, PARAFFINUM LIQUIDUM, PARFUM, CI 77266.

2. Pre-wax refreshing lotion: AQUA, ALCOHOL DENAT., POLYSORBATE 20, PROPYLENE GLYCOL, TREHALOSE, CALENDULA OFFICINALIS FLOWER EXTRACT, ALOE BARBADENSIS LEAF EXTRACT, ETHYLHEXYLGLYCERIN, PHENOXYETHANOL, CITRIC ACID, PANTHENOL, MENTHOL, PARFUM, PIROCTONE OLAMINE, BENZOPHENONE-4, COUMARIN, CI 15985.

3. After wax repair serum: AQUA, GLYCERIN, PEG-40 HYDROGENATED CASTOR OIL, TREHALOSE, UREA, SODIUM PCA, SODIUM LACTATE, ARGININE, ASPARTIC ACID, PCA, GLYCINE, ALANINE, SERINE, VALINE, PROLINE, THREONINE, ISOLEUCINE, HISTIDINE, PHENYLALANINE, CROTON LECHLERI RESIN EXTRACT, HYDROLYZED SOY PROTEIN, PANTHENOL, ALOE BARBADENSIS LEAF EXTRACT, XANTHAN GUM, ETHYLHEXYLGLYCERIN, PHENOXYETHANOL, POTASSIUM SORBATE, SORBIC ACID, PARFUM, BENZYL SALICYLATE, HYDROXYCITRONELLAL.

4. After wax protection mask: AQUA, CETEARYL ALCOHOL, PROPYLENE GLYCOL, ALCOHOL DENAT., KAOLIN, ZINC OXIDE, TETRASODIUM PYROPHOSPHATE, SULFUR, HYDROXYETHYLCELLULOSE, POLYSORBATE 20, CETEARETH-20, GLYCERYL STEARATE, PEG-100 STEARATE, AMMONIUM ACRYLOYLDIMETHYLTAURATE/VP COPOLYMER, ETHYLHEXYLGLYCERIN, TOCOPHERYL ACETATE, CITRIC ACID, PHENOXYETHANOL, CETRIMONIUM CHLORIDE, PARFUM.

5. Professional wax heater: housing material – ABS plastic, container material – aluminum.